复杂炼油塔模拟的改进联立方程内外层算法

在内外层算法的基础上，采用联立方程思想将主塔、侧线汽提塔视为一个整体进行建模，并针对复杂炼油塔的特点对算法提出了改进。首先，由于传统内外层法简化的K值模型对组成的变化不敏感，在处理带有石油的体系时，容易出现迭代次数较多，甚至部分塔板温度更新异常的问题，因此采用了汽相分数加和式推导了简化的K值模型加权因子。其次，借鉴流量加和法思想，规定侧线汽提塔的塔底产品流量作为设计变量，增强了算法收敛的稳定性。为验证改进后算法的有效性，采用不同的算法对实际的常压塔进行了模拟，结果显示改进后的算法适合应用于复杂炼油塔的模拟计算。     

生物质纤维和改性木质素对聚乳酸结晶性能的影响

采用改性木质素(MZS)作为成核剂,生物质纤维(BF)作为增强剂,通过双螺杆挤出机制备了生物降解的聚乳酸(PLA)/BF/MZS材料。采用差式扫量热仪(DSC)、电子万能试验机和扫描电子显微镜(SEM)分析了BF和MZS对PLA材料性能的影响。结果表明,BF和MZS有效提高了PLA的结晶能力和力学性能。当BF和MZS的含量分别为15%和1%时,PLA材料结晶度提高至67.1%,在50℃/min降温速率下仍具有较高的结晶能力。105℃等温结晶时,15%BF和1%MZS的PLA材料半结晶时间降低至9.0 s,比纯PLA缩短了72.2%。当PLA含有3%BF和1%MZS时,拉伸强度和冲击强度分别为70.1 MPa和7.4 kJ/m^2,比纯PLA分别提高了7.8%和10.4%,根据SEM显示,当BF含量为3%时,在PLA材料中分布较均匀。     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

Air torque position damper hysteresis

The purpose of this paper is to determine the effect of the air torque position (ATP) damper hysteresis on the accuracy of air velocity measurements and the adequacy of the ATP damper mathematical model tested in the present study. A total of three dampers with non-cascading blades were examined: a damper with a single flat blade, a damper with two opposed flat blades, and a damper with two flat blades - one of which is a measuring blade and the other is fixed in the horizontal direction. Furthermore, a total of two damper installation locations in a duct system were examined as well: at the duct exit with a straight duct section preceding the damper and within the duct itself with straight duct sections both preceding and following the damper. The ATP damper hysteresis was found to exert a significant effect on the accuracy of air velocity measurements and the adequacy of the ATP damper mathematical model tested if the ATP damper is more open, i.e. with lower blade angles of attack. Moreover, the ATP damper installed at the duct exit was found to be more susceptible to hysteresis effects than the damper located within the duct.     

旋转式采煤工艺在煤矿生产中的应用

采煤工艺作为煤矿正常生产的核心,直接关系到综采作业的效率、煤炭回采率和综采作业的安全性,随着对综采作业要求的不断提高,旋转式采煤工艺在煤矿井下的应用范围也不断扩大。以黄家沟煤业1205综采作业面为分析对象,对旋转式采煤工艺在井下的应用情况进行了研究,为优化综采方法、提升综采作业效率和煤炭回采率奠定基础。     

回转式空气预热器流场仿真分析

为分析某电厂1000 MW锅炉机组的双密封回转式空气预热器漏风问题,建立局部流体仿真模型。通过理论计算和仿真模拟相结合的方法分析了密封间隙对回转式空气预热器内部流场压力分布、密封压差及漏风率的影响,并针对“三密封”特殊时刻下的流场压力及漏风率变化做了研究。结果表明,密封间隙从2 mm到8 mm的变化过程中,密封片受到的最大压差小于7000 Pa;为使空预器漏风率小于5%,其漏风间隙需要控制在3 mm以内;“三密封”时刻下的漏风率达到了最小值,为3.98%。经过分析总结,为密封片的载荷计算及密封片的改进提供一定的参考。     

Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

On the limit theory of the Gaussian SQMLE in the EGARCH(1,1) model

We derive the limit theory of the Gaussian stable quasi maximum likelihood estimator for the stationary EGARCH(1,1) model when the squared innovation process has marginals with regularly varying tails. We derive regularly varying rates and limiting stable distributions. We perform Monte Carlo experiments to assess the extent of the parameter space corresponding to the invertibility condition, and the quality of the asymptotic approximation.     

不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

Performance of the LDA Volumetric Flow Rate Standard Under Severely Disturbed Flow Conditions

Flow meters in thermal power plants are operated at high temperatures and pressures and often encounter disturbed flow profiles. This leads to an increased measurement uncertainty, limiting the safe operating range of flow rates and thus, the plant's power output. To respond to this shortcoming, the laser optical flow rate standard (LFS) was developed. The LFS is designed to allow the on-site calibration of industrial flow meters in power plants at high temperatures and pressures. It makes use of the laser Doppler anemometry (LDA), as a fundamental and non-invasive method, to measure the velocity field simultaneously with two LDA systems. The volumetric flow rate is then determined by means of integration. Here, we present flow rate measurements for a fully developed pipe flow and for six pipe diameters downstream of a disturbance generator. The mean deviation in flow rate between the two LDA systems was 0.05%, with a mean deviation from the gravimetric reference flow rate of 0.12%. The highest deviations from the reference were 0.21% and 0.31%, for the first and second system respectively.